← Engine‑X atlas

Engine‑X machine guide

How does a manual gearbox work?

By Parth Parmar, mechanical design engineer · Updated

A manual gearbox changes how fast the wheels turn for each turn of the engine. All its gear pairs stay in mesh, but only one is locked to the shaft at a time. Moving the gear lever slides a synchroniser sleeve, which first matches the speeds and then locks the chosen gear to its shaft.

Engine-X 3D model of a 5-speed manual transaxle with see-through housing, input and output shafts, five helical gear pairs, synchroniser sleeves and blocker rings, shift forks, reverse idler and final drive gear
The Engine‑X manual gearbox 3D model, 47 named parts. Download it free (GLB, STL, every part) or view it in AR.

See it work: watch the gearbox step from neutral through 1st to 5th as the shift forks slide each synchro sleeve, compare the shaft speeds in every gear, then explode and cut open the box in 3D, free in your browser.

Open the 3D manual gearbox →

Or download the free 3D model (GLB, STL, AR).

Key facts

Type in the 3D model5-speed manual transaxle (gearbox + final drive in one case), two-shaft, synchromesh
1st gear50 : 12 = 4.167 : 1
2nd gear46 : 20 = 2.300 : 1
3rd gear43 : 30 = 1.433 : 1
4th gear41 : 38 = 1.079 : 1
5th gear40 : 47 = 0.851 : 1 (overdrive)
Reverse35 : 24 × 24 : 11 = 3.182 : 1, through an idler gear
Final drive69 : 14 = 4.929 : 1, so 1st overall is about 20.5 : 1
Reference gearboxVolkswagen 02T (Polo 1.0 L, code EJY), up to 200 N·m, 2.1 L of gear oil

How it works, step by step

  1. The engine turns the input shaft through the clutch. With the clutch pedal down, the input shaft is disconnected so a gear can be changed.
  2. Each forward gear is a pair: a drive gear on the input shaft meshing with a driven gear on the output shaft. All five pairs turn all the time; on each pair, one gear is free to spin on its shaft.
  3. In neutral, none of the free gears is locked, so the input shaft turns gears but no drive reaches the output shaft.
  4. Moving the gear lever slides a shift rail and its fork, which pushes a synchroniser sleeve towards the chosen gear.
  5. The brass blocker ring touches the gear’s cone first; friction brings the gear to the shaft’s speed. Only then can the sleeve slide over the gear’s dog teeth and lock it to the shaft.
  6. The drive now goes input shaft → chosen gear pair → output shaft → final drive pinion → differential → wheels. In 1st the output turns 4.17 times slower than the engine; in 5th it turns slightly faster.

Main parts of a manual gearbox

What does a synchroniser (synchro) do?

It matches the speed of the gear to the speed of the shaft before they lock together. The sleeve pushes a brass blocker ring onto a cone on the gear; friction speeds the gear up or slows it down, and the ring’s teeth hold the sleeve back until the speeds match. Then the sleeve slides onto the gear’s dog teeth.

Why does a manual gearbox grind when shifting?

A grind into one particular gear usually means that gear’s synchro ring is worn and can no longer match the speeds; 2nd often goes first. If every gear grinds, the clutch is probably not fully releasing. Low or wrong gear oil and rushed shifts make both worse.

SymptomLikely cause
One gear grindsWorn synchro ring for that gear
All gears grindClutch dragging, not fully released
Pops out of gearWorn synchro, dog teeth, fork or detent
Stiff when coldGear oil too thick for the temperature
Noise in every gearWorn shaft bearings or low oil

How does reverse gear work?

Reverse adds a third gear, the idler, between a gear on the input shaft and one on the output shaft. Each external mesh reverses the direction, so with three gears in the chain the output shaft turns backwards. Reverse is usually straight-cut and not synchronised, which is why it must be selected with the car stopped.

Common questions

Why are car gearbox gears always in mesh?

Constant mesh means the gears never slide in and out of each other, so the teeth are not damaged and helical teeth can be used, which are quieter and stronger. Changing gear only locks a different, already meshing gear to the shaft.

What is a gear ratio of 4.167 : 1?

It means the input shaft turns 4.167 times for one turn of the output shaft. In 1st the 12-tooth drive gear turns the 50-tooth driven gear: 50 ÷ 12 = 4.167. The output turns slower but with about 4.2 times the torque.

What is an overdrive gear?

A gear with a ratio below 1 : 1, where the output shaft turns faster than the engine. 5th in this gearbox is 0.851 : 1, which lowers the engine speed at motorway cruising.

What is a transaxle?

A gearbox combined with the final drive and differential in one case, as in most front-wheel-drive cars. The output shaft drives the differential directly, and the drive shafts come out of the sides of the gearbox.

How often should manual gearbox oil be changed?

It depends on the car; many makers call it lifetime fill, others give an interval. Low oil can wreck a manual gearbox within a few thousand miles, so check the level, especially if shifting gets stiff or noisy.

Sources

References for the facts on this page, and further reading:

Related reading on the blog

Timing belt vs timing chain: which lasts longer? · Open vs limited-slip vs locking differential

More machine guides

Compare: Belt vs chain vs gear drive: which is better?

How does a turbocharger work? · How does a centrifugal pump work? · How does a V-belt pulley drive work? · How does a gear reducer work? · Turbocharger vs supercharger: what's the difference? · Centrifugal vs positive displacement pump: what's the difference? · How does a marine diesel engine work? · How does a plate heat exchanger work? · How does a reciprocating air compressor work? · How does a planetary gearbox work? · How does a turbofan jet engine work? · How does a gate valve work? · How does a car differential work? · How does a car engine work? · How does an induction motor work? · How does a butterfly valve work?

Need an interactive 3D page like this for your own machine? See Work with Engine‑X.

From the Engine-X Journal

More on the manual gearbox: read the Engine-X Journal · how a manual gearbox works · free manual gearbox 3D model · play it in live 3D